Assigned to Quayson Ignacio, EC Date: 08/06.

verify hone/grind dimensions.

received. on QA table in shipping.

Vendor ran into issues with their system being done for a few day. They just advised: We just need to complete the certification.  If we can get that done today, the order can ship tomorrow.  Otherwise it will be Wednesday..

Vendor ran into issues with their system being done for a few day. They just advised: We just need to complete the certification.  If we can get that done today, the order can ship tomorrow.  Otherwise it will be Wednesday..

Vendor ran into issues with their system being done for a few day. They just advised: We just need to complete the certification.  If we can get that done today, the order can ship tomorrow.  Otherwise it will be Wednesday..

Vendor ran into issues with their system being done for a few day. They just advised: We just need to complete the certification.  If we can get that done today, the order can ship tomorrow.  Otherwise it will be Wednesday..

Vendor ran into issues with their system being done for a few day. They just advised: We just need to complete the certification.  If we can get that done today, the order can ship tomorrow.  Otherwise it will be Wednesday..

Vendor ran into issues with their system being done for a few day. They just advised: We just need to complete the certification.  If we can get that done today, the order can ship tomorrow.  Otherwise it will be Wednesday..

Pacmet is unable to confirm delivery due to their system being down.

Delay due to being short staffed, parts are at final QC..

Reached out this morning..

Confirmed off hold-shooting for 7/28 completion..

POC has been sent to the vendor. Purchase order has not been confirmed off hold yet..

Tyler submitted planning change..

Followed up with Tyler this morning..

Following up with Tyler today..

PO states to perform hardness test in the FN 7 location. That location is in the machined pockets – the indenter will not fit inside the pocket. We will need a different location to perform hardness testing. - Tyler looking into this. .

Looking into this, as it has not been delivered yet..

Pacmet EC: 7/8.

POC needed Friday, following up on recovery date today..

Working on recovery date..

Looks like frozen planning was approved this morning, will request recovery date today..

Customer has not yet provided an update..

No response from the customer yet..

Will follow up again today..

Tyler checking in on this approval today..

Frozen Planning submitted to the customer this morning, for approval..

Frozen Planning received from Pacmet.

Called this morning, should receive an update today..

Followed up again this morning..

Followed on the frozen planning this morning..

Pacmet working to submit a frozen planning..

Following up with Tyler today..

Another question came up, in regard to frozen planning. Tyler to look into this..

Off hold, recovery date requested..

Tyler to provide an update on this..

Customer meeting with Pacmet to discuss challenges on Wednesday. .

Reaching out EC today..

New EC: Invalid date (by Victor Da Silva on 05/09/25 06:52 AM) Assigned to , EC Date: Invalid date.

PACMET PO 64208.

6 parts good for HEAT TREAT.

Updated verbiage in Grind operation .

HF planning.

Router w/Shane.

Assigned to Shane Warnock, EC Date: 05/07.

Need to confirm OOT TP issue will be at grind before moving forward (heatmap).

OOT dims can be resolved at grind. Will update planning shortly to ensure that these dims/requirements are flowed to the grind OP. EXCEPT SN5, which calls out to a tangent point that will not be brought into tol after grind. B74 18 + .5 / -.00 @ 18.7 (18.560 AFTER GRIND) (SN:5) B28 T/P .05 @ .051 - .0572 (SN: 1 - 4) B33 59.98 + .019 / -.00 @ 60.005 (SN:1).

New EC: 05/06 (by Alex Limtiaco on 05/06/25 11:12 AM) New EC: 05/06 (by Alex Limtiaco on 05/06/25 11:10 AM) Assigned to Alex Limtiaco, EC Date: 05/05.

More investigation needed - AL (alex) working.

MOVED TO MRB QTY 5 OF 6 OOT- 5/2AM.

Assigned to Phil So, EC Date: 05/06.

null.

null. 6 good parts. 2 bad.

move to material stage .

Waiting on material.

Order is being ship today from Rolled Alloy. .

Machine: Ready <i class="fa-sharp fa-solid fa-shield-check text-success"></i> Material: HFM <i class="fa-sharp fa-solid fa-shield-check text-success"></i> Hardware: NA <i class="fa-sharp fa-solid fa-shield-check text-success"></i> Mod: Closed <i class="fa-sharp fa-solid fa-shield-check text-success"></i> Since Planned: 0 days Since Last Moved: 0 days .

Waiting on Material Purchase.

Planning change submitted 3/18.

Potential to change material, still on hold .

Meeting with customer to possibly change heat treat requirements. .

New EC: 03/18 (by Tyler Deis on 03/12/25 10:53 AM) Assigned to Tyler Deis, EC Date: 03/10.

Holding on production due to heat treat concerns. customer and I (tyler) are working though options. .

move to material stage.

In Programming.

Modified model created, dims verified. .

Modified model for unilateral tolerances currently in progress. Delay due to server issues forcing restart of work multiple times. .

In Programming.

Modified model for unilateral tolerances in progress..

New EC: 02/06 (by Zack Johnson on 02/05/25 10:26 AM) New EC: 02/05 (by Emily Marshall on 02/03/25 09:45 AM) New EC: 02/03 (by Zack Johnson on 01/30/25 04:53 PM) Assigned to Zack Johnson, EC Date: 01/30.

Dim Check.

New EC: 01/30 (by Ben Lo on 01/30/25 08:14 AM) Assigned to Ben Lo, EC Date: 01/29.

Assigned to Emily Marshall, EC Date: 01/30.

Material lead time in m days: available on OnlineMetals, can source elsewhere for longer lead times Needed material dock date: asap. Material risks and mitigation: expensive material, lots of process steps, will need extra parts Finishing/Processing risk and mitigation: Heat treat and carburization, outsource grinding Operational Complexity 1-10 scale: 8 Operation risks and mitigation: Complex part , long run time, high cost of material.